No results found for ""

Sign In
Portable Fire Equipment AS1851 Testing Equipment Fire Detection Systems VESDA & FAAST FLEX ASD Exit & Emergency Lighting Suppression Systems Fire Fighting Foam Water & Mechanical Passive Fire Equipment Fire Hydrant Landing Valves & Equipment Batteries Cable Cabinets Hardware & Fasteners Signage & Stickers Pro Audio - Public Address
UniWrap
UniWrap - picture 1
UniWrap - picture 2
UniWrap - picture 3
UniWrap - picture 4

UniWrap

Part Number: BUW-25

  • Universal length for versatility and ease of installation
  • Can provide fire rating for up to 35 x 100mm diameter pipes in a single roll
  • Can be used on plastic/PVC pipes as well as insulated or lagged metal pipes
  • High performance through high expansion rate
  • Halogen free, contains no asbestos, ceramic, mineral fibres and is environmentally friendly
  • Causes no known effects to plastic pipes, plastic cables, sheathing o r metallic components
  • Tested on uPVC, PP, MDPE + PE up to 200mm diameter
Category: Wraps Pipe Wraps Passive Fire Equipment
UniWrap
UniWrap - picture 1
UniWrap - picture 2
UniWrap - picture 3
UniWrap - picture 4

Technical Details

Width (mm):
60.0
Box Quantity:
1
Density:
1.3kg per meter cubed
Fire Rating:
2 Hour
Single Units:
Yes

Product Information

UniWrap® is an intumescent composition based on elastomeric thermoplastic polymers, binders and designed to provide high volume expansion and pressure seal. The product is fir e tested to multiple international Standards giving a f ire resistance of up to 4 hours, including EN1366 - 3 to - /120/120.

The pipes tested include PVC, Polypropylene, MDPE, HDPE, and HPPE up to a size of 200mm diameter pipes through concrete / blockwork floors and walls.

Benefits

  • Tested in Block Wall, Concrete and Masonry.
  • Tested in Concrete Floors.
  • Tested in large service openings up to 250 x 150mm.
  • Tested with Plastic Pipes – PVC, Polypropylene, MDPE, HDPE and HPPE.
  • Causes no known effects to plastic pipes, plastic cables, sheathing or metallic components.
  • Contributes to Green Building.
  • Shelf life of 5 years.
  • Suitable for wall and floor installation.
  • The product is based on a thermoplastic composite and is therefore non - toxic.
  • Halogen free, contains no asbestos, ceramic, mineral fibres and is environmentally friendly.
  • Not affected by fungus, vermin or rodents.
  • Remains flexible between - 40oC to +130oC, long life and is easy to use.

Specification

Pipe Diameter28mm, 32mm, 55mm, 63mm, 75mm, 82mm, 90mm, 110mm, 125mm, 160mm or 200mm
Width (Nominal)60mm
Thickness (Nominal)4mm up to 63mm, 6mm up to 110mm & 10mm thereafter
Density1.3 kg/m3
Volume Expansion at 300°C25 times
Fire Resistance2 hours

Installation

  1. Ensure the aperture for the pipe size has adequate annular gap for UniWrap® to be installed. Insert the pipe into the aperture.
  2. Using the measurements on the side of UniWrap ® box, cut the UniWrap® to the correct length to wrap fully around the pipe. Check the UniWrap® Configuration table for the number of layers required, depending on your pipe size.
  3. Wrap the UniWrap® around the pipe, securing to itself via the double sided tape. For a simpler installation ensure the double sided tape does not stick the UniWrap® to the pipe itself.
  4. Place additional layer(s) of wrap around the pipe if required, depending on your pipe size.
  5. Secure again with adhesive tape.
  6. Push the UniWrap® into the annular gap between the wall opening and the pipe. Adjust the position of the wrap so that the edge is central within the wall or floor surface.
  7. Seal over the top of the annular gap with FireMastic - 300 Sealant to a depth of 5mm. Smooth the finish with a small trowel or by hand. FireMastic - 300 can be cleaned up with water.
  8. Maintain record of installation.

Downloads

CATALOGUE PAGE

CATALOGUE PAGE - 475

SAFETY DATA SHEETS

SDS - UniWrap

TECHNICAL DATA SHEETS

TDS - UniWrap®